Olight S1 Baton

Olight S1 Baton Flashlight CREE XM-L2 CW LED 500lm

Worldwide Free shipping
by Registered Airmail with Tracking

Features:

• 
  Thumb sized form factor. diameter: 21mm length: 61mm
• Stainless steel flashlight head and switch binder ring processed by PVD
  technology
• Recessed silicon switch to prevent accidental operation
• TIR lens to create a balanced beam
• Positive polarity on the battery faces the tail of the flashlight for
  enhanced reliability and a more compact size
• Built-in timer: 3 minutes or 10 minutes
• Lanyard with perforating tool
• Flat tail cap design contains a strong magnet providing the ability to place
  it upside down and use it as a hands-free work light
• Removable pocket clip that is scratch resistant
• Thermal management safety program with overheat protection by dropping high
  output by 50% within 1 minute of constant on. Turbo mode has a limit of 1.5
  minutes.
• The S1 features a wide range current circuit and can be powered by 1 x
  CR123A (built-in protected board)
• Reverse polarity protection to prevent improper battery installation

Specifications:

• Cree XM-L2 LED. Maximum light output up to 500 lumens.
• 3 standard modes: 8 lumens, 80 lumens and 500 lumens.
• 2 special modes: 0.5 lumen moonlight mode and a 10Hz strobe mode.
• 6061-T6 aluminum alloy body with anti-scratch Type-III hard anodizing
• PMMA TIR lens with a 90% light transmittance rate
• Low standby current below 10uA
• Body material: 6061-T6 aluminum alloy structure, Type III hard anodizing
• Stainless steel pocket clip, stainless steel flashlight bezel, stainless
  steel binder ring
• Dimensions: Length: 61mm, Diameter: 21mm
• Weight : 30g (excluding batteries)
• Color （body + clip）black，（BEZEL+ side switch binder ring）blue
• Operating voltage: 2.5 to 4.2V
• Luminous Intensity: 3000 cd
• Max beam distance: 110 meters
• Waterproof: IPX8

This product has the following specifications (ANSI/NEMA FL1-2009 Standards):

Operation:

• Single click — Turn ON / Turn OFF
• Click and hold — High brightness, select timer, or activate moon light
  mode
• Quick double click — Turbo brightness, or enter setting
• Quick triple click — strobe mode

Run times and outputs by battery type:

* High: Max – 500 lumens（RCR123A 3.7V), Max – 500 lumens（CR123A 3.0V）


Operation Details:

Remove the flashlight and battery from the package. Make sure that the negative
polarity side of the battery is facing the head of flashlight. install the
battery and screw the tail cap on tightly.

Turn ON/OFF: single click the side switch. When you turn on the light, the
output level will return to the last output mode (except strobe mode).

Changing brightness level: With the light on, press and hold the side switch.
the output will cycle through low, medium, and high brightness levels. Release
the side switch when the desired brightness level is achieved.

Moon light mode: when the light is off, click and hold the side switch for 1
second and the moon light mode will activate. If the light is turned off while
on moon light mode, single clicking the side switch will automatically return
the light to moon light mode.
How to activate the high brightness output when the light is off: quickly double
click the side switch.

Strobe mode: triple-click the side switch to activate strobe mode. Click the
side switch once to quit strobe mode.

Timer: The S1 contains two timer settings: long timer (10 minutes) and short
timer (3 minutes). Double click the side switch to enter this setting. short
timer blink for 3 minutes, long time blink for 10 minutes. Double click the side
switch to change the timer to the opposite setting. After the setting is saved,
the light will blink 3 times and then will enter the timer mode. The light will
automatically shut off when the timer is over.

Package Contains

• 1 × Flashlight
• 1 × lanyard
• User manual